View LXZ2-2780-Y_8366976.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

key applications ? indoor area ? lamps - mr16, par, gu10 and candles ? outdoor area - high-fux street light modules ? specialty lighting ? architectural luxeon z and luxeon z es datasheet ds120 ?2013 philips lumileds lighting company. features ? micro sized: luxeon z, 1.3x1.7 mm and luxeon z es, 1.6x2.0 mm ? undomed device architecture ? hot tested at 85c ? up to 1 a max drive current ? freedom from binning ? 1, 3, 5 step mce options ? lowest thermal resistance 3c/w benefts ? highest luminance to deliver punch ? ultimate design fexibility from micro form factor ? precise optical control from an undomed architecture ? enables small customizable and scalable light engines ? leading system level lm/$ proposition luxeon z luxeon z es breakthrough luminance, design fexibility and optical control for illumination solutions introduction philips lumileds technology enables the new luxeon ? z and luxeon z es leds. the luxeon z is a family of micro sized illumination grade emitters that is the frst ever 1-step macadam ellipse warm white led that enables never before seen color consistency, luminance, fux density and design fexibility for next generation lighting solutions. luxeon z family is undomed, a feature that provides un-matched optical fexibility for precise beam angle control. tested and binned at application conditions 85c, the luxeon z and z es emitters are an ideal choice for indoor and outdoor light sources requiring superior beam angles, higher effciency and lower costs.
luxeon z and luxeon z es datasheet ds120 20130517 ?2013 philips lumileds lighting company. i table of contents general information 2 product nomenclature 2 average lumen maintenance characteristics 2 environmental compliance 2 product selection 3 optical characteristics 4 electrical characteristics 4 absolute maximum ratings 5 jedec moisture sensitivity 5 mechanical dimensions of luxeon z es 6 mechanical dimensions of luxeon z 7 solder pad design 8 relative spectral distribution 9 light output characteristics 10 typical spatial radiation pattern 14 emitter pocket tape packaging for luxeon z es 16 emitter reel packaging for luxeon z es 16 emitter pocket tape packaging for luxeon z 17 emitter reel packaging for luxeon z 18 product binning and labeling 19 luminous flux and forward voltage bins 20 luxeon z and luxeon z es: 1-step, 3-step (above and below blackbody) and 5-step mac adam ellipse color defnition 21
luxeon z and luxeon z es datasheet ds120 20130517 ?2013 philips lumileds lighting company. 2 general information product nomenclature luxeon z and z es emitters are specifed and binned under hot conditions comparable to those found in real-world lighting products. the test conditions for luxeon z es and luxeon z are 700 ma dc and 500 ma dc respectively with junction temperature at 85c the part number designation is explained as follows: l x z n - a b c d - y where: n 1 for luxeon z and 2 for luxeon z es a, b designates nominal ansi cct (27 for 2700k, 30 for 3000k, rb for royal blue) c, d designates minimum cri performance (7 for 70 cri, 8 for 80 cri, 9 for 90 cri) y 1 designates 1 sdcm, 3 designates 3 sdcm and 5 designates 5 sdcm (only for 80 and 90 cri versions. lower than equal to 70 cri parts will not have a sdcm designate and all parts will be within 5 step mce). therefore, 3 sdcm 2700k/80 cri luxeon z es will have the following part number: l x z 2 C 2 7 8 0 - 3 therefore, 5 sdcm 3000k/80 cri luxeon z will have the following part number: l x z 1 C 3 0 8 0 - 5 average lumen maintenance characteristics luxeon z products are tested in compliance with lm-80. please visit www.philipslumileds.com/support/documentation/ lumen-maintenance or contact your local philips lumileds technical solutions manager for tm-21 extrapolations or other support. environmental compliance philips lumileds is committed to providing environmentally friendly products to the solid-state lighting market. luxeon z and luxeon z es products are compliant to the european union directives on the restriction of hazardous substances in electronic equipment, namely the rohs and reach directives. philips lumileds will not intentionally add the following restricted material to the luxeon z and luxeon z es: lead, mercury, cadmium, hexavalent chromium, polybrominated biphenyls (pbb) or polybrominated diphenyl ethers (pbde).
luxeon z and luxeon z es datasheet ds120 20130517 ?2013 philips lumileds lighting company. 3 product selection product selection guide for luxeon z es emitters junction temperature = 85c table 1. luxeon z es @ 700 ma @ 1a @ 350 ma part number normal cct / cri min flux (lm) typ fux (lm) ty p vf typ lm/w typ fux (lm) ty p vf typ lm/w typ fux (lm) ty p vf typ lm/w LXZ2-2780-Y 2700 / 80 160 175 2.85 88 224 2.90 77 99 2.77 102 lxz2-2790-y 2700 / 90 110 135 2.85 68 178 2.90 61 78 2.77 81 lxz2-3080-y 3000 / 80 160 180 2.85 91 238 2.90 82 104 2.77 108 lxz2-3090-y 3000 / 90 120 145 2.85 73 178 2.90 61 78 2.77 81 lxz2-3580-y 3500 / 80 170 190 2.85 95 244 2.90 84 107 2.77 111 lxz2-4080-y 4000 / 80 180 195 2.85 98 257 2.90 89 113 2.77 117 lxz2-4070 4000 / 70 190 210 2.85 106 277 2.90 96 122 2.77 126 lxz2-5070 5000 / 70 200 215 2.85 108 284 2.90 98 125 2.77 129 lxz2-5770 5700 / 70 200 215 2.85 108 284 2.90 98 125 2.77 129 notes for table 1: 1. all luxeon z es emitters are tested and binned at 700 ma/85c. 2. philips lumileds maintains a tolerance of 6.5% on luminous fux and 2 on cri measurements. product selection for luxeon z emitters junction temperature = 85c table 2. luxeon z @ 500 ma @ 700 ma @ 350 ma part number normal cct / cri min flux (lm) typ fux (lm) ty p vf typ lm/w typ fux (lm) ty p vf typ lm/w typ fux (lm) ty p vf typ lm/w lxz1-2780-y 2700 / 80 90 105 2.85 74 134 2.89 66 81 2.81 82 lxz1-3080-y 3000 / 80 100 110 2.85 78 141 2.89 70 85 2.81 86 lxz1-4080-y 4000 / 80 100 126 2.85 89 161 2.89 80 97 2.81 99 lxz1-4070 4000 / 70 100 132 2.85 93 169 2.89 84 102 2.81 103 lxz1-5070 5000 / 70 110 142 2.85 100 182 2.89 90 109 2.81 111 lxz1-5770 5700 / 70 110 148 2.85 104 189 2.89 94 114 2.81 116 lxz1-6565 6500 / 65 110 135 2.85 95 173 2.89 85 104 2.81 106 notes for table 2: 1. all luxeon z emitters above are tested and binned at 500 ma/85c. 2. philips lumileds maintains a tolerance of 6.5% on luminous fux and 2 on cri measurements.
luxeon z and luxeon z es datasheet ds120 20130517 ?2013 philips lumileds lighting company. 4 optical characteristics luxeon z es at test current 700 ma, junction temperature 85c & luxeon z at test current 500 ma, junction temperature 85c table 3. nominal ansi cct color temperature cct typical typical total included angle 2 (degrees) u 0 90v typical viewing angle 3 (degrees) 2 u 1/2 2700k 2725k 160 120 3000k 3045k 160 120 3500k 3465k 160 120 4000k 3985k 160 120 5000k 5028k 160 120 5700k 5665k 160 120 notes for table 3: 1. total angle at which 90% of total luminous fux is captured. 2. viewing angle is the off axis angle from lamp centerline where the luminous intensity is ? of the peak value. electrical characteristics luxeon z es at test current 700 ma, junction temperature 85c & luxeon z at test current 500 ma, junction temperature 85c table 4. nominal ansi cct forward voltage v, 1 (v) typical temperature coeffcient of forward voltage 2 (mv/c) d v f / d t j typical thermal resistance junction to thermal pad (c/w) r u j-c min max 2700k 2.5 3.25 -1.6 3 3000k 2.5 3.25 -1.6 3 3500k 2.5 3.25 -1.6 3 4000k 2.5 3.25 -1.6 3 5000k 2.5 3.25 -1.6 3 5700k 2.5 3.25 -1.6 3 6500k 2.5 3.25 -1.6 3 notes for table 4: 1. philips lumileds maintains a tolerance of 0.06v on forward voltage measurements. 2. measured between t = 25c and t = 110c at i = 700 ma.
luxeon z and luxeon z es datasheet ds120 20130517 ?2013 philips lumileds lighting company. 5 absolute maximum ratings table 5. parameter luxeon z es luxeon z dc forward current (ma) 1, 2 1050 700 peak pulsed forward current (ma) 1, 3 1200 1000 esd sensitivity < 8000v human body model (hbm) class 3a jesd22-a114-e < 8000v human body model (hbm) class 3a jesd22-a114-e led junction temperature 1 135c 135c operating case temperature at 700 ma -40c - 135c -40c - 135c storage temperature -40c - 135c -40c - 135c soldering temperature jedec 020c 260c jedec 020c 260c allowable refow cycles 3 3 reverse voltage (vr) 5, 6 luxeon z leds are not designed to be driven in reverse bias notes for table 5: 1. proper current derating must be observed to maintain junction temperature below the maximum. for additional information on thermal measurement guidelines please refer to application brief ab106. 2. residual periodic variations due to power conversion from alternating current (ac) to direct current (dc), also called ripple, with frequencies 3. 100 hz and amplitude 200 ma are acceptable, assuming the average current throughout each cycle does not exceed 1000 ma. 4. pulsed operation with a peak drive current of 1200 ma is acceptable if the pulse on-time is 5 ms per cycle and the duty cycle is 50% 5. transient reverse voltages and surge currents due to electrical switching or supply interruptions are acceptable if these events do not last for more than 10ms, the amplitude of the reverse voltage does not exceed 5v and the reverse current is less than 200a. 6. max 5v reverse for up to 10s is an acceptable beginning of life, one time test condition. jedec moisture sensitivity table 6. level floor life soak requirements standard time conditions time conditions 1 unlimited v 30c / 85% rh 168h + 5 / - 0 85c / 85% rh
luxeon z and luxeon z es datasheet ds120 20130517 ?2013 philips lumileds lighting company. 6 mechanical dimensions of luxeon z es notes for figure 1: 1. do not handle the device by the lens. excessive force on the lens may damage the lens itself or the interior of the device. 2. drawings not to scale. 3. all dimensions are in millimeters. 4. the thermal pad is electrically isolated from the anode and cathode contact pads. ??????????? ??????????? ??????????? ??????????? ??????????? ??????????? ??????????? ????? ??????? ??????????? ??????????? ??????????? ??????????? ?????????????? ??????????? ??????????? figure 1. package outline drawing for luxeon z es.
luxeon z and luxeon z es datasheet ds120 20130517 ?2013 philips lumileds lighting company. 7 mechanical dimensions of luxeon z notes for figure 2: 1. do not handle the device by the lens. excessive force on the lens may damage the lens itself or the interior of the device. 2. drawings not to scale. 3. all dimensions are in millimeters. 4. the thermal pad is electrically isolated from the anode and cathode contact pads. figure 2. package outline drawing for luxeon z.
luxeon z and luxeon z es datasheet ds120 20130517 ?2013 philips lumileds lighting company. 8 solder pad design notes for figure 3: 1. the drawing above shows the recommended solder pad layout on printed circuit board (pcb). 2. application brief ab202 provides extensive details for this layout. in addition, the .dwg fles are available at www.philipslumileds.com and www.philipslumileds.cn.com. figure 3. layout design b. recommended pcb footprint for luxeon z es for high component count density based on solder mask defned pads. dimensions in mm.. figure 4. solder pad layout for luxeon z.
luxeon z and luxeon z es datasheet ds120 20130517 ?2013 philips lumileds lighting company. 9 relative spectral distribution relative spectral distribution vs wavelength characteristics figure 5.
luxeon z and luxeon z es datasheet ds120 20130517 ?2013 philips lumileds lighting company. 10 light output characteristics relative light output vs thermal pad temperature for luxeon z es, test current at 700 ma relative light output vs forward current for luxeon z es, thermal pad temperature = 85c figure 6. figure 7.
luxeon z and luxeon z es datasheet ds120 20130517 ?2013 philips lumileds lighting company. 11 forward current characteristics for luxeon z es, thermal pad temperature = 85c figure 8.
luxeon z and luxeon z es datasheet ds120 20130517 ?2013 philips lumileds lighting company. 12 relative light output vs thermal pad temperature for luxeon z white, test current at 500 ma relative light output vs forward current for luxeon z white, thermal pad temperature = 85c figure 9. figure 10.
luxeon z and luxeon z es datasheet ds120 20130517 ?2013 philips lumileds lighting company. 13 forward current characteristics for luxeon z white, thermal pad temperature = 85c figure 11.
luxeon z and luxeon z es datasheet ds120 20130517 ?2013 philips lumileds lighting company. 14 typical spatial radiation pattern luxeon z es luxeon z es typical polar radiation pattern figure 12. figure 13.
luxeon z and luxeon z es datasheet ds120 20130517 ?2013 philips lumileds lighting company. 15 typical spatial radiation pattern luxeon z luxeon z typical polar radiation pattern 0% 20% 40% 60% 80% 100% 120% -90 -75 -60 -45 -30 -15 0 15 30 45 60 75 90 relative intensity (%) anglular displacement (deg) white (lxz1-4070) figure 14. 0 0.2 0.4 0.6 0.8 1 0 30 60 90 120 150 180 -150 -120 -90 -60 -30 white (lxz1-4070) figure 15.
luxeon z and luxeon z es datasheet ds120 20130517 ?2013 philips lumileds lighting company. 16 emitter pocket tape packaging for luxeon z es notes for figure 16: 1. all dimensions are in millimeters emitter reel packaging for luxeon z es figure 16. emitter pocket tape packaging for luxeon z es. figure 17. emitter reel packaging for luxeon z es.
luxeon z and luxeon z es datasheet ds120 20130517 ?2013 philips lumileds lighting company. 17 emitter pocket tape packaging for luxeon z notes for figure 18: 1. all dimensions are in millimeters figure 18. emitter pocket tape packaging for luxeon z.
luxeon z and luxeon z es datasheet ds120 20130517 ?2013 philips lumileds lighting company. 18 emitter reel packaging for luxeon z figure 19. emitter reel packaging for luxeon z.
luxeon z and luxeon z es datasheet ds120 20130517 ?2013 philips lumileds lighting company. 19 product binning and labeling purpose of product binning in the manufacturing of semiconductor products, there are variations in performance around the average values given in the technical data sheets. for this reason, philips lumileds bins the led components for luminous fux and forward voltage (v f ). color is offered in a single 1 step, 3-step or 5-step macadam ellipse color space centered on the ansi cct color bins. for additional information please review the macadam ellipse technical defnition section. decoding product bin labeling luxeon z es and luxeon z emitters are labeled using a four digit alphanumeric code (cat code) depicting the bin values for emitters packaged on a single reel. all emitters packaged within a reel are of the same 3-variable bin combination. reels of luxeon z emitters are labeled with a four digit alphanumeric cat code following the format below. abcd a = flux/radiometric power bin (l, m, etc.) b and c = color bin (5a, 5b, 5c, 5d, 3u, 3l, 01) d = v f bin (p, r)
luxeon z and luxeon z es datasheet ds120 20130517 ?2013 philips lumileds lighting company. 20 luminous flux and forward voltage bins table 7 lists the standard photometric luminous fux bins for luxeon z es and luxeon z emitters (tested and binned at 700 ma and 500 ma t j = 85c). although several bins are outlined, product availability in a particular bin varies by production run and by product performance. not all bins are available in all colors. bin code minimum photometric flux (lm) maximum photometric flux (lm) a 100 110 b 110 120 c 120 130 d 130 140 e 140 150 f 150 160 g 160 170 h 170 180 j 180 190 k 190 200 l 200 210 m 210 220 n 220 230 p 230 240 table 8 lists minimum and maximum v f bin values per emitter. although several bins are outlined, product availability in a particular bin varies by production run and by product performance. bin code minimum forward voltage (v) maximum forward voltage (v) p 2.50 2.75 r 2.75 3.00 s 3.00 3.25
luxeon z and luxeon z es datasheet ds120 20130517 ?2013 philips lumileds lighting company. 21 luxeon z and luxeon z es: 1-step, 3-step (above and below blackbody) and 5-step macadam ellipse color defnition table 9. luxeon z and luxeon z es 1-step macadam ellipse parameters nominal ansi cct color space center point (cx, cy) major axis, a minor axis, b ellipse rotation angle 2700k single 1-step macadam ellipse (0.4578, 0.4101) 0.00270 0.00140 53.70 3000k single 1-step macadam ellipse (0.4338, 0.4030) 0.00278 0.00136 53.22 3500k single 1-step macadam ellipse (0.4073, 0.3917) 0.00309 0.00138 54.00 table 10. luxeon z and luxeon z es 3-step macadam ellipse parameters nominal ansi cct color space center point (cx, cy) major axis, a minor axis, b ellipse rotation angle 2700k single 3-step macadam ellipse (0.4578, 0.4101) 0.00810 0.00420 53.7 3000k single 3-step macadam ellipse (0.4338, 0.4030) 0.00834 0.00408 53.2 3500k single 3-step macadam ellipse (0.4073, 0.3917) 0.00927 0.00414 54.0 4000k single 3-step macadam ellipse (0.3818, 0.3797) 0.00939 0.00402 53.7 5000k single 3-step macadam ellipse (0.3447, 0.3553) 0.00822 0.00354 59.6 table 11. luxeon z and luxeon z es 5-step macadam ellipse parameters nominal ansi cct color space center point (cx, cy) major axis, a minor axis, b ellipse rotation angle 2700k single 5-step macadam ellipse (0.4578, 0.4101) 0.01350 0.00700 53.7 3000k single 5-step macadam ellipse (0.4338, 0.4030) 0.01390 0.00680 53.2 3500k single 5-step macadam ellipse (0.4073, 0.3917) 0.01545 0.00690 54.0 4000k single 5-step macadam ellipse (0.3818, 0.3797) 0.01565 0.00670 53.7 5000k single 5-step macadam ellipse (0.3447, 0.3553) 0.01370 0.00590 59.6 5700k single 5-step macadam ellipse (0.3287, 0.3417) 0.01243 0.00533 59.09 note for tables 9, 10 & 11: ? philips lumileds maintains a tester tolerance of 0.005 on x, y color coordinates. roh s compliant b1 b2 b3 b4 bin 3u [1] bin 3l [2] 1-step mae 3-step mae bbl [1] color bin 3u denotes the area above bbl enclosed by 3-step mae and (outside) 1-step mae [2] color bin 3l denotes the area below bbl enclosed by 3-step mae and (outside) 1-step mae b1 to b4 are intersection points on bbl color space defnition for above and below blackbody parameter defnition of macadam ellipse
company information philips lumileds is a leading provider of leds for everyday lighting applications. the companys records for light output, effcacy and thermal management are direct results of the ongoing commitment to advancing solid-state lighting technology and enabling lighting solutions that are more environmentally friendly, help reduce co2 emissions and reduce the need for power plant expansion. philips lumileds luxeon ? leds are enabling never before possible applications in outdoor lighting, shop lighting, home lighting, digital imaging, display and automotive lighting. philips lumileds is a fully integrated supplier, producing core led material in all three base colors, (red, green, blue) and white. philips lumileds has r&d centers in san jose, california and in the netherlands, and production capabilities in san jose, singapore and penang, malaysia. founded in 1999, philips lumileds is the high fux led technology leader and is dedicated to bridging the gap between solid-state technology and the lighting world. more information about the companys luxeon led products and solid-state lighting technologies can be found at www philipslumileds com. luxeon z and luxeon z es datasheet ds120 20130517 ?2013 philips lumileds lighting company. all rights reserved. luxeon is a registered trademark of the philips lumileds lighting company in the united states and other countries. www philipslumileds com www philipslumileds cn com philips lumileds lighting company shall not be liable for any kind of loss of data or any other damages, direct, indirect or consequential, resulting from the use of the provided information and data. although philips lumileds lighting company has attempted to provide the most accurate information and data, the materials and services information and data are provided as is and philips lumileds lighting company neither warranties, nor guarantees the contents and correctness of the provided information and data. philips lumileds lighting company reserves the right to make changes without notice. you as user agree to this disclaimer and user agreement with the download or use of the provided materials, information and data.

▲Up To Search▲

Price & Availability of LXZ2-2780-Y

	To Download LXZ2-2780-Y Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .